Hydrophilic aliphatic polyisocyanate based on pentamethylene diisocyanate (PDI) for waterborne two-component polyurethane systems.
Product description
Applications
Bayhydur® CQ ultra 701-90 PGDA is a low odour crosslinking agent for waterborne systems where reliable incorporation and high chemical resistances are required. Despite its relatively low hydrophilic properties this hardener can be easily dispersed in the aqueous phase, even at low shear forces such as typically found in trade applications where manual mixing is required. Further dilution could be necessary for proper miscibility.The product has good miscibility with both acrylic polyols as well as polyurethane dispersions. Bayhydur® CQ ultra 701-90 PGDA can be used as a crosslinking partner for waterborne polyol binders (Bayhydrol®) and as a crosslinker for roughly pH-neutral waterborne polymer dispersions such as polyurethane, polyvinyl acetate, polyacrylate and synthetic rubber dispersions.After addition of Bayhydur® CQ ultra 701-90 PGDA, the ready-to-use two-component formulation must be used within the pot life. This is not only influenced by the polymer content but also by the other components (resin, thickener, plasticizer,etc.). Comparable to other dispersions the end of the pot life usually several hours is not marked by gelling.
Form supplied
approx. 90 % in propylene glycol diacetate
Specification
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| NCO content | 17.5 - 18.5 | % | M105-ISO 11909 | |
| Viscosity | at 23 °C | approx. 5,000 | mPa*s | M014-ISO 3219/A.3 |
| Color value | (Hazen) | < 60 | M017-EN 1557 | |
| Monomeric PDI | < 0.1 | % | M106-ISO 10283 |
Typical Values
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Biobased Carbon | in supply form | approx. 61 | % | ASTM D 6866-16Method B (AMS) |
| Equivalent weight | approx. 235 | |||
| Density at 20 °C | approx. 1.19 | g/cm3 | DIN 51757 | |
| Flash point | approx. 106 | °C | DIN EN ISO 2719 |
Solubility / thinnability
Bayhydur® CQ ultra 701-90 PGDA is generally compatible with organic solvents such as esters or ethers. However, the solubility/compatibility should be tested in each individual case. Only PU grade solvents should be used (< 0.05 % water).
Storage
- Storage in original sealed Covestro container. - Recommended storage temperature: 0 - 30 °C. - Protect from moisture, heat and foreign material. General information: Hydrophilic isocyanates are very moisture-sensitive and react with water to form carbon dioxide and insoluble ureas. The containers must always be kept tightly closed. The access of water in all forms (moist air, solvents, moist containers) must be prevented, because the generation of carbon dioxide can lead to dangerous increases in pressure. Storage at higher temperatures will result in an increase of color and viscosity.
Storage time
Covestro represents that, for a period of six months following the day of shipment as stated in the respective transport documents, the product will meet the specifications or values set forth in section "specifications or characteristic data" above, what ever is applicable, provided that the product is stored in full compliance with the storage conditions set forth in and referenced under section "storage" above and is otherwise handled appropriately.The lapse of the six months period does not necessarily mean that the product no longer meets specifications or the set values. However, prior to using said product, Covestro recommends to test such a product if it still meets the specifications or the set values. Covestro does not make any representation regarding the product after the lapse of the six months period and Covestro shall not be responsible or liable in any way for the product failing to meet specifications or the set values after the lapse of the six months period.
Health and Safety Information
Before working with this product, you must read and become familiar with the available information on its risks, proper use, and handling. Information is available in several forms, e.g., in particular in the currently valid safety data sheets and product labels. For further information contact your Covestro representative.
Disclaimer
General
The manner in which you use our products, technical assistance and information (whether verbal, written or by way of production evaluations), including any suggested formulations and recommendations, are beyond our control. Therefore, it is imperative that you test our products to determine suitability for your processing and intended uses. Your analysis must at least include testing to determine suitability from a technical, health, safety, and environmental and regulatory standpoint. Such testing has not necessarily been done by Covestro, and Covestro has not obtained any approvals or licenses for a particular use or application of the product.
Unless we otherwise agree in writing, all products are sold strictly pursuant to the terms of our standard conditions of sale which are available upon request.
All information and including technical assistance is given without warranty or guarantee and is subject to change without notice. It is expressly understood and agreed by you that you assume and hereby expressly release indemnify us and hold us harmless from all liability, in tort, contract or otherwise, incurred in connection with the use of our products, technical assistance, and information. Any statement or recommendation not contained herein is unauthorized and shall not bind us. Nothing herein shall be construed as a recommendation to use any product in conflict with any claim of any patent relative to any material or its use. No license is implied or in fact granted under the claims of any patent.
Trial or development Product
This is a trial product. Further information, including amended or supplementary data on hazards associated with its use, may be compiled in the future. For this reason no assurances are given as to type conformity, processability, long-term performance characteristics or other production or application parameters. Therefore, the purchaser/user uses the product entirely at his own risk without having been given any warranty or guarantee and agrees that the supplier shall not be liable for any damage, of whatever nature, arising out of such use. Commercialisation and continued supply of this material are not assured. Its supply may be discontinued at any time.
Non Medical and non Food Contact
This product is not designated for the manufacture of a medical device or of intermediate products for medical devices (1). This product is also not designated for other specifically regulated applications (e.g. including cosmetics, plant protection, fertilisers, plant strengtheners, food processing, food contact and others). If the intended use of the product is for the manufacture of a medical device or of intermediate products for medical devices or for other specifically regulated applications Covestro must be contacted in advance to provide its agreement to sell such product for such purpose. Nonetheless, any determination as to whether a product is appropriate for use in a medical device or intermediate products for medical devices, for Food Contact products or cosmetic applications must be made solely by the purchaser of the product without relying upon any representations by Covestro.
1) Please see the Guidance on Use of Covestro Products in a Medical Application document.
Sample
Any samples provided by Covestro are for testing purposes only and not for commercial use.
Typical value
These values are typical values only. Unless explicitly agreed in written form, they do not constitute a binding material specification or warranted values
Contact
Please use our contact form or contact us directly by sending an e-mail to technical-datasheets@cx.covestro.com .
