Before working with this product, you must read and become familiar with the available information regarding its risks, proper use, and safe handling. This information is provided in various formats, including the current Safety Data Sheet (SDS) and product label. SDS can be accessed via the following link:
Safety Data Sheets (SDS) for Covestro products | Covestro
For further questions, please use the contact information provided on this technical data sheet.
Product description
Polyester-Polyurethane dispersion which dries by oxidation.As a binder in the formulation of aqueous air- and forced-drying, high-gloss coatings and primers with very good anti-corrosion properties. Mainly used for general industrial finishes.
Applications
Coatings based on this resin show a quick drying and after drying a quite high hardness. After curing over night a very good water-resistance is achievable. High-gloss coatings, however, need a certain amount of suitable co-solvents and additional amine in the formulation. Primers based on Bayhydrol® UH 2592 perform with an excellent corrosion resistance.Bayhydrol® UH 2592 can be used as universal resin for high-gloss top coats, effect coats and - due to its excellent anti-corrosion properties – as raw material for primers and single coats.Bayhydrol® UH 2592 shows a very good shear-stability and is therefore recommendable for dip applications, too.
Form supplied
Approx. 45% in water, neutralized with ethyldiisopropylamine (EDIPA), ratio approx. 53.5 : 1.5
Specification
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Viscosity | at 23 °C, D = approx. 40 s^-1 | max. 600 | mPa*s | DIN EN ISO 3219/A.3 |
| Non-volatile content | (1 g/1 h/125 °C) | 43 - 47 | % | DIN EN ISO 3251 |
| pH | 6,0 - 7,5 | DIN ISO 976 |
Typical Values
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Mean particle size | approx. 125 | nm | photon correlation spectroscopy | |
| Appearance of supply form | milky, cloudy | |||
| Density | at 20 °C | approx. 1,0 | g/ml | DIN EN ISO 2811 |
| OH content (calculated on solid resin) | approx. 2,1 | % | ||
| Acid value | approx. 12 | mg KOH/g | DIN EN ISO 2114 | |
| Alternative raw material share | 1) bio-based | approx. 23 | wt.-% | calculated |
| Alternative carbon share | 1) bio-based | approx. 29 | % | calculated |
Compatibility
Combination with other aqueous binders is possible but should be tested in every single case. All standard inert and alkaline pigments can be used to colour formulations based on Bayhydrol® UH 2592.
Storage
- Storage in original sealed Covestro containers. - Recommended storage temperature: 5 - 23 °C. - Protect from frost. General information: The product freezes at temperatures below 0 °C and may be damaged. It must therefore be stored frost-free.
Storage time
Covestro represents that, for a period of six months following the day of shipment as stated in the respective transport documents, the product will meet the specifications or values set forth in section "specifications or characteristic data" above, what ever is applicable, provided that the product is stored in full compliance with the storage conditions set forth in and referenced under section "storage" above and is otherwise handled appropriately.The lapse of the six months period does not necessarily mean that the product no longer meets specifications or the set values. However, prior to using said product, Covestro recommends to test such a product if it still meets the specifications or the set values. Covestro does not make any representation regarding the product after the lapse of the six months period and Covestro shall not be responsible or liable in any way for the product failing to meet specifications or the set values after the lapse of the six months period.
Processing
Bayhydrol® UH 2592 in its supply form is neutralized to approx. 60% with ethyldiisopropylamine. To achieve a better pigment wetting additional amounts of amine (ethyldiisopropylamine, triethylamine or - in case of forced drying – dimethylethanolamine) are recommended. The additional amine should be added to the mill base and should target a neutralization degree of 80 – 100%, depending on the pigmentation.Addition of amine causes a significant increase of viscosity.Please take additional advice for handling and formulation from the starting point formulations.
All established water-mixable driers may be used.
Health and Safety Information
Disclaimer
Responsibility and Liability
The use of Covestro products, technical assistance, and information (regardless of how provided) is outside Covestro’s control and is solely the responsibility of the customer. The customer must conduct adequate testing to determine the suitability of products for its intended use, including but not limited to technical, health, safety, and environmental aspects. Unless otherwise agreed in writing, all products are sold exclusively under Covestro’s standard conditions of sale, which prevail in case of conflict and are available upon request.
The terms and conditions of sale and delivery are available via the following link:
https://order.covestro.com/covestrostorefront/saleConditions
All information is provided “as is” without warranties, express or implied, including merchantability or fitness for a particular purpose, and is subject to change without notice. To the maximum extent permitted by law, Covestro disclaims, and the customer assumes all liability for losses, damages, or claims arising out of use of Covestro products, technical assistance, or information. Any statement or recommendation not expressly contained in Covestro documentation is unauthorized and shall not bind Covestro. Nothing herein shall be construed as encouraging or recommending the use of any product in conflict with any claim of any patent. No license is implied or in fact granted under the claims of any patent.
Restrictions on Regulated Applications
This product is not intended for use in regulated applications such as agriculture, cosmetics, drinking water contact, food contact, medical products (e.g., medical devices), toys, or similar uses subject to specific regulatory requirements. Prior written approval from Covestro is required before this product may be used in any regulated application. The customer is solely responsible for ensuring compliance with all applicable laws and determining product suitability. Covestro disclaims all liability and warranties for unauthorized regulated uses.
Typical Value
The values provided are typical only and do not represent binding specifications. Unless expressly confirmed in a written contract, these values are not part of the contractual quality agreement and must not be relied upon as a warranty or guarantee of product performance.
Sample
Samples provided by Covestro are intended solely for evaluation and testing purposes by the customer and may not be used in commercial applications, resold, transferred to third parties (except qualified testing service providers acting on behalf of the customer), reverse engineered, modified, or used in any manner not explicitly authorized in writing by Covestro. Samples are provided ‘as-is’ without any warranties, express or implied, including fitness for a particular purpose. Customers are solely responsible for ensuring safe handling, regulatory compliance, and suitability of the material for their intended evaluations. Covestro disclaims all liability for damages or losses arising from the use of samples.
Contact Information
Please use our contact form or contact us directly by sending an e-mail to technical-datasheets@cx.covestro.com .
