Applications
Injection molding; General purpose
Sustainability
Partially bio-circular grade / Attributed via mass balance (according to ISCC PLUS Standard). For specific content see sustainability declaration.
Typical Values
Rheological properties
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Melt Volume-flow Rate (MVR) | 300 °C/ 1.2 kg | 19 | cm³/10 min | ISO 1133-1 |
| Molding Shrinkage, parallel | 60x60x2 mm/ 500 bar | 0.65 | % | ISO 294-4 |
| Molding Shrinkage, normal | 60x60x2 mm/ 500 bar | 0.7 | % | ISO 294-4 |
| Molding Shrinkage, parallel / normal | Value range based on general practical experience | 0.5 - 0.7 | % | b.o. ISO 2577 |
Mechanical properties (23 °C/50 % r. h.)
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Tensile modulus | 1 mm/min | 2,400 | MPa | ISO 527-1,-2 |
| Yield Stress | 50 mm/min | 65 | MPa | ISO 527-1,-2 |
| Yield Strain | 50 mm/min | 6 | % | ISO 527-1,-2 |
| Nominal Strain at Break | 50 mm/min | > 50 | % | ISO 527-1,-2 |
| Strain at Break | 50 mm/min | 125 | % | b.o. ISO 527-1,-2 |
| Stress at Break | 50 mm/min | 65 | MPa | ISO 527-1,-2 |
| Flexural Modulus | 2 mm/min | 2,350 | MPa | ISO 178 |
| Flexural Strength | 2 mm/min | 97 | MPa | ISO 178 |
| Flexural Strain at Flexural Strength | 2 mm/min | 7.1 | % | ISO 178 |
| Flexural Stress at 3.5 % Flexural Strain | 2 mm/min | 73 | MPa | ISO 178 |
| Izod Notched Impact Strength | -30 °C/ 3 mm | 15 | kJ/m² | ISO 21305/based on ISO 180/A |
| Izod Notched Impact Strength | 23 °C/ 3 mm | 65 | kJ/m² | ISO 21305/based on ISO 180/A |
| Charpy Notched Impact Strength | -30 °C/ 3 mm | 14 | kJ/m² | ISO 21305/based on ISO 179/1eA |
| Charpy Notched Impact Strength | 23 °C/ 3 mm | 65 | kJ/m² | ISO 21305/based on ISO 179/1eA |
| Puncture Impact Properties - Maximum Force | -30 °C | 6,000 | N | ISO 6603-2 |
| Puncture Impact Properties - Maximum Force | 23 °C | 5,100 | N | ISO 6603-2 |
| Puncture Energy | -30 °C | 65 | J | ISO 6603-2 |
| Puncture Energy | 23 °C | 55 | J | ISO 6603-2 |
| Ball Indentation Hardness | 115 | N/mm² | ISO 2039-1 | |
| Tensile Creep Modulus | 1000 h | 1,900 | MPa | ISO 899-1 |
| Tensile Creep Modulus | 1 h | 2,200 | MPa | ISO 899-1 |
Thermal properties
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Temperature of Deflection under Load | 0.45 MPa | 137 | °C | ISO 75-1,-2 |
| Temperature of Deflection under Load | 1.80 MPa | 124 | °C | ISO 75-1,-2 |
| Vicat Softening Temperature | 50 N; 120 °C/h | 146 | °C | ISO 306 |
| Vicat Softening Temperature | 50 N; 50 °C/h | 145 | °C | ISO 306 |
| Glass Transition Temperature | 10 °C/min | 144 | °C | ISO 11357-1,-2 |
| Coefficient of Linear Thermal Expansion, parallel | 23 to 55 °C | 0.65 | 10⁻⁴/K | ISO 11359-1,-2 |
| Coefficient of Linear Thermal Expansion, normal | 23 to 55 °C | 0.65 | 10⁻⁴/K | ISO 11359-1,-2 |
| Burning Behavior | 2.7 mm | HB | UL 94 | |
| Burning Behavior | 0.36 mm | V - 2 | UL 94 | |
| Burning Behavior | 0.75 mm | V - 2 | UL 94 | |
| Burning Rate (US-FMVSS-302) | >=1.0 mm | PASSED | ISO 3795 | |
| Oxygen Index | Method A | 27 | % | ISO 4589-2 |
| Thermal Conductivity, through-plane | 23 °C; 50 % r. h. | 0.2 | W/(m·K) | ISO 8302 |
| Resistance to Heat (Ball Pressure Test) | 136 | °C | IEC 60695-10-2 | |
| Relative Temperature Index (Tensile Impact Strength) | 1.5 mm | 115 | °C | UL 746B |
| Relative Temperature Index (Electric Strength) | 1.5 mm | 125 | °C | UL 746B |
| Glow Wire Test (GWFI) | 3.0 mm | 930 | °C | IEC 60695-2-12 |
| Glow Wire Test (GWFI) | 1.5 mm | 875 | °C | IEC 60695-2-12 |
| Glow Wire Test (GWFI) | 0.75 mm | 850 | °C | IEC 60695-2-12 |
| Glow Wire Test (GWIT) | 3.0 mm | 875 | °C | IEC 60695-2-13 |
| Glow Wire Test (GWIT) | 1.5 mm | 875 | °C | IEC 60695-2-13 |
| Glow Wire Test (GWIT) | 1.0 mm | 875 | °C | IEC 60695-2-13 |
| Glow Wire Test (GWIT) | 0.75 mm | 875 | °C | IEC 60695-2-13 |
| Application of Flame from Small Burner | Method K and F/ 2.0 mm | K1, F1 | DIN 53438-1,-3 | |
| Needle-flame Test | Method F/ 3.0 mm | 120 | °C | IEC 60695-11-5 |
| Needle-flame Test | Method F/ 2.0 mm | 120 | °C | IEC 60695-11-5 |
| Needle-flame Test | Method F/ 1.5 mm | 60 | °C | IEC 60695-11-5 |
| Needle-flame Test | Method K/ 3.0 mm | 10 | °C | IEC 60695-11-5 |
| Needle-flame Test | Method K/ 2.0 mm | 5 | °C | IEC 60695-11-5 |
| Needle-flame Test | Method K/ 1.5 mm | 5 | °C | IEC 60695-11-5 |
| Flash-Ignition Temperature | 480 | °C | ASTM D1929 | |
| Self-Ignition Temperature | 550 | °C | ASTM D1929 |
Electrical properties (23 °C/50 % r. h.)
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Relative Permittivity | 1 MHz | 3 | IEC 60250 | |
| Relative Permittivity | 100 Hz | 3.1 | IEC 60250 | |
| Dielectric Dissipation Factor | 1 MHz | 90 | 10⁻⁴ | IEC 60250 |
| Dielectric Dissipation Factor | 100 Hz | 5 | 10⁻⁴ | IEC 60250 |
| Volume Resistivity | 1E14 | Ω·m | IEC 62631-3-1 | |
| Surface Resistivity | 1E16 | Ω | IEC 62631-3-2 | |
| Electric Strength | 1 mm | 34 | kV/mm | IEC 60243-1 |
| Comparative Tracking Index (CTI) | Solution A | 250 | IEC 60112 | |
| Comparative Tracking Index (CTI M) | Solution B | 125 | IEC 60112 | |
| Electrolytic Corrosion | A1 | IEC 60426 |
Other properties (23 °C)
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Water Absorption (Saturation Value) | Water at 23 °C | 0.3 | % | ISO 62 |
| Water Absorption (Equilibrium Value) | 23 °C; 50 % r. h. | 0.12 | % | ISO 62 |
| Water Vapour Transmission Rate | 23 °C; 85 % RH/ 100 µm film | 15 | g/(m²·24 h) | ISO 15106-1 |
| Density | 1,200 | kg/m³ | ISO 1183-1 | |
| Bulk Density | Pellets | 660 | g/cm³ | ISO 60 |
| Gas Permeation | Carbon dioxide/ 25.4 µm (1 mil) film | 18,900 | cm³/(m²·24 h·bar) | b.o. ISO 2556 |
| Gas Permeation | Carbon dioxide/ 100 µm film | 4,000 | cm³/(m²·24 h·bar) | b.o. ISO 2556 |
| Gas Permeation | Nitrogen/ 25.4 µm (1 mil) film | 630 | cm³/(m²·24 h·bar) | b.o. ISO 2556 |
| Gas Permeation | Nitrogen/ 100 µm film | 130 | cm³/(m²·24 h·bar) | b.o. ISO 2556 |
| Gas Permeation | Oxygen/ 25.4 µm (1 mil) film | 3,150 | cm³/(m²·24 h·bar) | b.o. ISO 2556 |
| Gas Permeation | Oxygen/ 100 µm film | 700 | cm³/(m²·24 h·bar) | b.o. ISO 2556 |
Material specific properties
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Luminous Transmittance (Clear Transparent Materials) | 4 mm | 87 | % | ISO 13468-2 |
| Luminous Transmittance (Clear Transparent Materials) | 3 mm | 88 | % | ISO 13468-2 |
| Luminous Transmittance (Clear Transparent Materials) | 2 mm | 89 | % | ISO 13468-2 |
| Luminous Transmittance (Clear Transparent Materials) | 1 mm | 89 | % | ISO 13468-2 |
| Haze for Transparent Materials | 3 mm | < 0.8 | % | ISO 14782 |
| Refractive Index | Procedure A | 1.585 | ISO 489 |
Processing conditions for test specimens
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Injection Molding - Melt Temperature | 280 | °C | ISO 294 | |
| Injection Molding - Mold Temperature | 80 | °C | ISO 294 | |
| Injection Molding - Injection Velocity | 200 | mm/s | ISO 294 |
Recommended processing and drying conditions
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Standard Melt Temperature | 300 | °C | ||
| Barrel Temperatures | 290 - 300 | °C | ||
| Barrel Temperatures | 280 - 290 | °C | ||
| Barrel Temperatures | 270 - 280 | °C | ||
| Barrel Temperatures | 250 - 260 | °C | ||
| Mold Temperatures | 80 - 120 | °C | ||
| Hold Pressure (% of Injection Pressure) | 50 - 75 | % | ||
| Plastic Back Pressure (specific) | 50 - 150 | bar | ||
| Peripheral Screw Speed | 0.05 - 0.2 | m/s | ||
| Shot-to-Cylinder Size | 30 - 70 | % | ||
| Dry Air Drying Temperature | 120 | °C | ||
| Dry Air Drying Time | 2 - 3 | h | ||
| Moisture Content max. (%) | ≤ 0.02 | % | ||
| Vent Depth | 0.025 - 0.075 | mm |
