Covestro certifies that the product meets specifications for 6 months from the date of shipment, provided it is stored and handled in accordance with the conditions specified in the ‘Storage’ section. After this period, product performance is not assured; Customers are responsible for retesting material before use. Covestro assumes no liability for product performance after 6 months.
Product description
Desmodur CD-C is a pale yellow-coloured, modified diphenylmethane 4,4' diisocyanate which is liquid at room temperature. It is used among other things, as the isocyanate component in the production of polyurethane.
Sampling
Moisture access must be prevented when taking product samples.
Specification
| Property | Value | Unit | Standard |
|---|---|---|---|
| NCO content | 28,50 - 29,50 | % by wt. | MDI-01-01 |
| Viscosity at 25° C | 20,0 - 50,0 | mPa.S | MDI-01-02 |
| Hydrolysable chlorine | ≤ 50 | mg/kg | MDI-01-04 |
Typical Values
| Property | Value | Unit | Standard |
|---|---|---|---|
| Density at 25° C | 1.22 ± 0.02 | g/cm³ | DIN 51757 |
| Phenyl isocyanate content | ≤ 10 | ppm | MDI-01-09 |
These values provide general information and are not part of the product specification
Storage
Recommended storage temperature: +15℃ to +30℃
Drums should be protected against strong sunlight and always kept sealed to protect the content from moisture or damp air.
Storage time
Processing
Desmodur CD-C is moisture-sensitive and should therefore always be stored in moisture-tight containers. Prolonged storage at temperatures in excess of 30℃ leads to a deterioration in quality as the product becomes increasingly cloudy due to the deposition of low solubility sediment (dimer formation). If the recommended storage temperature is exceeded for a long period (especially if the temperature of the product rises to above 50℃), or if the recommended shelf life is excessed, a chemical reaction may take place. In addition to a reduction in the NCO content and an increase in viscosity, carbon dioxide in particular may be generated. The resultant increase in pressure may cause the container to swell or burst. Storage at below 15℃ results in crystallization. Desmodur CD-C should under no circumstances be stored in crystallized form as this will promote the formation of insoluble dimers and it will no longer be possible to melt the product completely. Delivered product should be spot–check for crystallization, and cooling to below 15℃ must be avoided. If Desmodur CD-C has been transported or stored below 15℃ for a short time, the material must be re-melted immediately at 60 - 70℃. The melting point and the time required for this should not be exceeded as this also significantly promotes dimer formation. The entire container contents must be melted and homogenized before the container is immediately tightly resealed and its contents cooled down to the recommended storage temperature. There is no risk that quality will be affected should be product have crystallized briefly, but it can be expected that the shelf life will be reduced. The melted material should be used as soon as possible.
Health and Safety Information
Before working with this product, you must read and become familiar with the available information regarding its risks, proper use, and safe handling. This information is provided in various formats, including the current Safety Data Sheet (SDS) and product label. SDS can be accessed via the following link:
Safety Data Sheets (SDS) for Covestro products | Covestro
For further questions, please use the contact information provided on this technical data sheet.
Disclaimer
Responsibility and Liability
The use of Covestro products, technical assistance, and information (regardless of how provided) is outside Covestro’s control and is solely the responsibility of the customer. The customer must conduct adequate testing to determine the suitability of products for its intended use, including but not limited to technical, health, safety, and environmental aspects. Unless otherwise agreed in writing, all products are sold exclusively under Covestro’s standard conditions of sale, which prevail in case of conflict and are available upon request.
The terms and conditions of sale and delivery are available via the following link:
https://order.covestro.com/covestrostorefront/saleConditions
All information is provided “as is” without warranties, express or implied, including merchantability or fitness for a particular purpose, and is subject to change without notice. To the maximum extent permitted by law, Covestro disclaims, and the customer assumes all liability for losses, damages, or claims arising out of use of Covestro products, technical assistance, or information. Any statement or recommendation not expressly contained in Covestro documentation is unauthorized and shall not bind Covestro. Nothing herein shall be construed as encouraging or recommending the use of any product in conflict with any claim of any patent. No license is implied or in fact granted under the claims of any patent.
Restrictions on Regulated Applications
This product is not intended for use in regulated applications such as agriculture, cosmetics, drinking water contact, food contact, medical products (e.g., medical devices), toys, or similar uses subject to specific regulatory requirements. Prior written approval from Covestro is required before this product may be used in any regulated application. The customer is solely responsible for ensuring compliance with all applicable laws and determining product suitability. Covestro disclaims all liability and warranties for unauthorized regulated uses.
Typical Value
The values provided are typical only and do not represent binding specifications. Unless expressly confirmed in a written contract, these values are not part of the contractual quality agreement and must not be relied upon as a warranty or guarantee of product performance.
Sample
Samples provided by Covestro are intended solely for evaluation and testing purposes by the customer and may not be used in commercial applications, resold, transferred to third parties (except qualified testing service providers acting on behalf of the customer), reverse engineered, modified, or used in any manner not explicitly authorized in writing by Covestro. Samples are provided ‘as-is’ without any warranties, express or implied, including fitness for a particular purpose. Customers are solely responsible for ensuring safe handling, regulatory compliance, and suitability of the material for their intended evaluations. Covestro disclaims all liability for damages or losses arising from the use of samples.
Contact Information
Please use our contact form or contact us directly by sending an e-mail to technical-datasheets@cx.covestro.com .
