Submit

Makrolon® 2405 MAS057

MVR (300 °C/1.2 kg) 19 cm³/10 min; improved impact strength; low viscosity; easy release

Contact expert Request a sample Request a quote
i
Market Switch
Selection will influence the results you get.
Copied to clipboard

About

Product Types

No data available

Material

No data available

General Characterization

No data available

Storage Conditions

No data available

Sampling

No data available

Packaging Type

No data available

Technical Properties & Datasheets

Property Name Standard Test condition Unit Value
Barrel Temperatures - Front - °C 280 - 290
Barrel Temperatures - Middle - °C 270 - 280
Barrel Temperatures - Nozzle - °C 290 - 300
Barrel Temperatures - Rear - °C 250 - 260
Dry Air Drying Temperature - °C 120
Dry Air Drying Time - h 2 - 3
Hold Pressure (% of injection pressure) - % 50 - 75
Melt temperatures - °C 280 - 320
Moisture Content max. (%) - % <= 0,02
Mold Temperatures - °C 80 - 120
Peripheral Screw Speed - m/s 0.05 - 0.2
Plastic Back Pressure (specific) - bar 50 - 150
Shot-to-Cylinder Size - % 30 - 70
Standard Melt temperature - °C 300
Vent Depth - mm 0.025 - 0.075
Property Name Standard Test condition Unit Value
Burning rate (US-FMVSS) ISO 3795 >=1.0 mm mm/min passed
Coefficient of linear thermal expansion, normal ISO 11359-1,-2 23 to 55 °C 10^-4^/K 0.65
Coefficient of linear thermal expansion, parallel ISO 11359-1,-2 23 to 55 °C 10^-4^/K 0.65
Flash ignition temperature ASTM D1929 °C 460
Glow wire test (GWFI) IEC 60695-2-12 1.0 mm °C 800
Glow wire test (GWFI) IEC 60695-2-12 1.5 mm °C 800
Glow wire test (GWFI) IEC 60695-2-12 2.0 mm °C 850
Glow wire test (GWFI) IEC 60695-2-12 3.0 mm °C 930
Glow wire test (GWFI) IEC 60695-2-12 4.0 mm °C 960
Glow wire test (GWIT) IEC 60695-2-13 1.0 mm °C 825
Glow wire test (GWIT) IEC 60695-2-13 1.5 mm °C 825
Glow wire test (GWIT) IEC 60695-2-13 2.0 mm °C 825
Glow wire test (GWIT) IEC 60695-2-13 3.0 mm °C 850
Glow wire test (GWIT) IEC 60695-2-13 4.0 mm °C 850
Oxygen index ISO 4589-2 Method A % 30
Resistance to heat (ball pressure test) IEC 60695-10-2 °C 136
Self ignition temperature ASTM D1929 °C 540
Temperature of deflection under load ISO 75-1,-2 0.45 MPa °C 136
Temperature of deflection under load ISO 75-1,-2 1.80 MPa °C 123
Thermal conductivity, through-plane ISO 8302 23 °C; 50 % r. h. W/(m*K) 0.2
Vicat softening temperature ISO 306 50 N; 120 °C/h °C 144
Vicat softening temperature ISO 306 50 N; 50 °C/h °C 143
Property Name Standard Test condition Unit Value
Ball indentation hardness ISO 2039-1 N/mm² 113
Charpy impact strength ISO 179/1eU -30 °C kJ/m² N
Charpy impact strength ISO 179/1eU -60 °C kJ/m² N
Charpy impact strength ISO 179/1eU 23 °C kJ/m² N
Charpy notched impact strength ISO 21305/based on ISO 179/1eA -30 °C/ 3 mm kJ/m² 16C
Charpy notched impact strength ISO 21305/based on ISO 179/1eA 23 °C/ 3 mm kJ/m² 60P
Flexural modulus ISO 178 2 mm/min MPa 2400
Flexural strain at flexural strength ISO 178 2 mm/min % 6.8
Flexural strength ISO 178 2 mm/min MPa 93
Flexural stress at 3.5 % strain ISO 178 2 mm/min MPa 72
Izod notched impact strength ISO 21305/based on ISO 180/A 23 °C/ 3 mm kJ/m² 60P
Izod notched impact strength ISO 21305/based on ISO 180/A -30 °C/ 3 mm kJ/m² 15C
Nominal strain at break ISO 527-1,-2 50 mm/min % > 50
Puncture energy ISO 6603-2 -30 °C J 55
Puncture energy ISO 6603-2 23 °C J 50
Puncture impact properties - maximum force ISO 6603-2 -30 °C N 5800
Puncture impact properties - maximum force ISO 6603-2 23 °C N 4900
Strain at break b.o. ISO 527-1,-2 50 mm/min % 115
Stress at break ISO 527-1,-2 50 mm/min MPa 65
Tensile modulus ISO 527-1,-2 1 mm/min MPa 2400
Yield strain ISO 527-1,-2 50 mm/min % 5.8
Yield stress ISO 527-1,-2 50 mm/min MPa 62
Property Name Standard Test condition Unit Value
Melt mass-flow rate ISO 1133 300 °C/ 1.2 kg g/10 min 20
Melt volume-flow rate ISO 1133 300 °C/ 1.2 kg cm³/10 min 19
Molding shrinkage, normal ISO 294-4 60x60x2 mm³/ 500 bar % 0.7
Molding shrinkage, parallel ISO 294-4 60x60x2 mm³/ 500 bar % 0.65
Molding shrinkage, parallel/normal b.o. ISO 2577 Value range based on general practical experience % 0.5 - 0.7
Property Name Standard Test condition Unit Value
Comparative tracking index CTI IEC 60112 Solution A Rating 250
Comparative tracking index CTI M IEC 60112 Solution B Rating 125M
Dissipation factor IEC 60250 1 MHz 10^-4^ 110
Dissipation factor IEC 60250 100 Hz 10^-4^ 10
Electrical strength IEC 60243-1 1 mm kV/mm 34
Electrolytic corrosion IEC 60426 Rating A1
Relative permittivity IEC 60250 1 MHz 3.0
Relative permittivity IEC 60250 100 Hz 3.1
Surface resistivity IEC 62631-3-2 Ohm 1E16
Volume resistivity IEC 62631-3-1 Ohm*m 1E14
Property Name Standard Test condition Unit Value
Injection molding - Injection velocity ISO 294 mm/s 200
Injection molding - Melt temperature ISO 294 °C 280
Injection molding - Mold temperature ISO 294 °C 80
Property Name Standard Test condition Unit Value
Bulk density ISO 60 Pellets kg/m³ 640
Density ISO 1183-1 kg/m³ 1200
Water absorption (equilibrium value) ISO 62 23 °C; 50 % r. h. % 0.12
Water absorption (saturation value) ISO 62 Water at 23 °C % 0.3

Downloads

Technical Data Sheet
Download
Safety Data Sheet
No direct download available, please visit www.productsafetyfirst.covestro.com

Related topics

Do you want to know more about Makrolon® 2405 MAS057?
Get in touch with our experts!

How would you describe yourself?

What type of material are you interested in?

What type of industry are you interested in?

What type of inquiry is this?

How can we contact you?

* Mandatory Fields

{"FieldName":"","Endpoint":"https://covestro-prod-ffm.apimanagement.eu2.hana.ondemand.com/hybrispcm/products_typeahead?identKey=GB6LiyNSG0YYxXXEpmO8EyoUdFLN0Roi&max=5&lang=en&extended=true","Language":"en","PermissionQuery":"","BrandLabel":"Brand","ProductLabel":"Product","NoResultLabel":"No results for","MaxItem":10}
Request a sample
formVersion
{"FieldName":"productName","Endpoint":"https://covestro-prod-ffm.apimanagement.eu2.hana.ondemand.com/hybrispcm/products_typeahead?identKey=GB6LiyNSG0YYxXXEpmO8EyoUdFLN0Roi&max=5&lang=en&extended=true","Language":"en","PermissionQuery":"","BrandLabel":"Brand","ProductLabel":"Product","NoResultLabel":"No results for","MaxItem":10}

Request a sample

Hello! Thanks for reaching out to us.
We have received your request and one of our experts will be in touch with you as soon as possible.
In the meantime, feel free to discover our innovative material solutions!

Speak to you soon,
Your Covestro Team

Request a quote
formVersion
{"FieldName":"productName","Endpoint":"https://covestro-prod-ffm.apimanagement.eu2.hana.ondemand.com/hybrispcm/products_typeahead?identKey=GB6LiyNSG0YYxXXEpmO8EyoUdFLN0Roi&max=5&lang=en&extended=true","Language":"en","PermissionQuery":"","BrandLabel":"Brand","ProductLabel":"Product","NoResultLabel":"No results for","MaxItem":10}

Request a quote

Hello! Thanks for reaching out to us.
We have received your request and one of our experts will be in touch with you as soon as possible.
In the meantime, feel free to discover our innovative material solutions!

Speak to you soon,
Your Covestro Team

Compare