- Plastics
Apec® 1895
MVR (330°C/2.16kg) 18 cm³/10 min; easy release; 'softening temperature (VST/B 120)=183°C; Covers for brake lights and indicator lights; Recessed light fixtures/reflectors; Raised brake lights; Headlamp reflectors/bezels
i
Market Switch
Selection will influence the results you get.
About
Product Types
- Polycarbonate
Material
- พลาสติก
- Heat resistant
General Characterization
No data available
Storage Conditions
No data available
Sampling
No data available
Packaging Type
No data available
Technical Properties & Datasheets
| Property Name | Standard | Test condition | Unit | Value |
|---|---|---|---|---|
| Barrel Temperatures - Front | - | °C | 315 - 325 | |
| Barrel Temperatures - Middle | - | °C | 305 - 315 | |
| Barrel Temperatures - Nozzle | - | °C | 325 - 335 | |
| Barrel Temperatures - Rear | - | °C | 295 - 305 | |
| Dry Air Drying Temperature | - | °C | 130 | |
| Dry Air Drying Time | - | h | 2 - 3 | |
| Hold Pressure (% of injection pressure) | - | % | 50 - 75 | |
| Melt temperatures | - | °C | 330 - 340 | |
| Moisture Content max. (%) | - | % | <= 0,02 | |
| Mold Temperatures | - | °C | 120 - 140 | |
| Peripheral Screw Speed | - | m/s | 0.05 - 0.2 | |
| Plastic Back Pressure (specific) | - | bar | 50 - 150 | |
| Shot-to-Cylinder Size | - | % | 30 - 70 | |
| Standard Melt temperature | - | °C | 335 | |
| Vent Depth | - | mm | 0.025 - 0.075 |
| Property Name | Standard | Test condition | Unit | Value |
|---|---|---|---|---|
| Burning behavior UL 94 (1.5 mm) | UL 94 | 1.5 mm | Class | HB |
| Coefficient of linear thermal expansion, normal | ISO 11359-1,-2 | 23 to 55 °C | 10^-4^/K | 0.65 |
| Coefficient of linear thermal expansion, parallel | ISO 11359-1,-2 | 23 to 55 °C | 10^-4^/K | 0.65 |
| Glow wire test (GWFI) | IEC 60695-2-12 | °C | 850 | |
| Oxygen index | ISO 4589-2 | Method A | % | 25 |
| Relative temperature index (Electric strength) | UL 746B | °C | 150 | |
| Relative temperature index (Tensile impact strength) | UL 746B | °C | 130 | |
| Relative temperature index (Tensile strength) | UL 746B | °C | 150 | |
| Temperature of deflection under load | ISO 75-1,-2 | 0.45 MPa | °C | 174 |
| Temperature of deflection under load | ISO 75-1,-2 | 1.80 MPa | °C | 157 |
| Vicat softening temperature | ISO 306 | 50 N; 120 °C/h | °C | 183 |
| Property Name | Standard | Test condition | Unit | Value |
|---|---|---|---|---|
| Ball indentation hardness | ISO 2039-1 | N/mm² | 127 | |
| Charpy impact strength | ISO 179/1eU | -30 °C | kJ/m² | N |
| Charpy impact strength | ISO 179/1eU | 23 °C | kJ/m² | N |
| Flexural modulus | ISO 178 | 2 mm/min | MPa | 2400 |
| Flexural strength | ISO 178 | 2 mm/min | MPa | 108 |
| Nominal strain at break | ISO 527-1,-2 | 50 mm/min | % | > 50 |
| Tensile modulus | ISO 527-1,-2 | 1 mm/min | MPa | 2350 |
| Yield strain | ISO 527-1,-2 | 50 mm/min | % | 6.7 |
| Yield stress | ISO 527-1,-2 | 50 mm/min | MPa | 72 |
| Property Name | Standard | Test condition | Unit | Value |
|---|---|---|---|---|
| Luminous transmittance (clear transparent materials) | ISO 13468-2 | 1 mm | % | 89 |
| Refractive index | ISO 489 | Procedure A | 1.573 |
| Property Name | Standard | Test condition | Unit | Value |
|---|---|---|---|---|
| Melt mass-flow rate | ISO 1133 | 330 °C/ 2.16 kg | g/10 min | 19 |
| Melt volume-flow rate | ISO 1133 | 330 °C/ 2.16 kg | cm³/10 min | 18 |
| Molding shrinkage, normal | ISO 294-4 | 60x60x2 mm³ | % | 0.85 |
| Molding shrinkage, parallel | ISO 294-4 | 60x60x2 mm³ | % | 0.85 |
| Property Name | Standard | Test condition | Unit | Value |
|---|---|---|---|---|
| Comparative tracking index CTI | IEC 60112 | Solution A | Rating | 300 |
| Comparative tracking index CTI M | IEC 60112 | Solution B | Rating | 100 |
| Dissipation factor | IEC 60250 | 1 MHz | 10^-4^ | 80 |
| Dissipation factor | IEC 60250 | 100 Hz | 10^-4^ | 10 |
| Electrical strength | IEC 60243-1 | 1 mm | kV/mm | 35 |
| Electrolytic corrosion | IEC 60426 | Rating | A1 | |
| Relative permittivity | IEC 60250 | 1 MHz | 2.8 | |
| Relative permittivity | IEC 60250 | 100 Hz | 2.9 | |
| Surface resistivity | IEC 62631-3-2 | Ohm | 1E16 | |
| Volume resistivity | IEC 62631-3-1 | Ohm*m | 1E15 |
| Property Name | Standard | Test condition | Unit | Value |
|---|---|---|---|---|
| Injection molding - Injection velocity | ISO 294 | mm/s | 200 | |
| Injection molding - Melt temperature | ISO 294 | °C | 330 | |
| Injection molding - Mold temperature | ISO 294 | °C | 100 |
| Property Name | Standard | Test condition | Unit | Value |
|---|---|---|---|---|
| Density | ISO 1183-1 | kg/m³ | 1150 | |
| Water absorption (equilibrium value) | ISO 62 | 23 °C; 50 % r. h. | % | 0.12 |
| Water absorption (saturation value) | ISO 62 | Water at 23 °C | % | 0.3 |
Downloads
-
Technical Data Sheet
-
Safety Data SheetNo direct download available, please visit www.productsafetyfirst.covestro.com
-
Spannung-Dehnung Apec® 1895 (Multipoint Data Sheet) Stress-Strain Apec® 1895 (Multipoint Data Sheet)
-
Sekantenmodul-Dehnung Apec® 1895 (Multipoint Data Sheet) Secant modulus - Strain Apec® 1895 (Multipoint Data Sheet)
-
Viskosität Schergeschwindigkeit Apec® 1895 (Multipoint Data Sheet) Viscosity Shear Rate Apec® 1895 (Multipoint Data Sheet)
