Desmodur® CQ T 80 MS - for flexible foams
Desmodur CQ T 80 MS is a mixture of the two isomeric forms 2,4-toluene diisocyanate and 2,6-toluene diisocyanate in the ratio 80:20. Desmodur CQ T 80 MS is used for the production of polyurethanes. Our certified Desmodur CQ T 80 MS has a share of approx. 52% bio-circular feedstock attributed via the mass balance approach
i
Market Switch
Selection will influence the results you get.
About
Product Types
No data available
Material
No data available
General Characterization
Desmodur CQ T 80 MS is a mixture of the two isomeric forms 2,4-toluene diisocyanate [A] and 2,6-toluene diisocyanate [B] in the ratio 80:20. Desmodur CQ T 80 MS is used for the production of polyurethanes. Our certified Desmodur CQ T 80 MS has a share of approx. 52% bio-circular feedstock attributed via the mass balance approach.
Storage Conditions
- Storage in original sealed Covestro container.
- Recommended storage temperature: 18 - 40°C.
- Protect from moisture, heat and foreign material.
General information:
The product is sensitive to moisture and heat. It should be protected against contact with atmospheric moisture. Higher storage temperatures for prolonged periods may result in discoloration or the formation of insoluble deposits. The product crystallizes at temperatures below 18°C. However, careful melting at up to 50°C will reliquify the product without any detrimental effect on its quality. The contact surface temperature may not exceed 80°C. The reliquified product must be homogenized as crystallisation causes a shift in the isomer ratio between the crystalline and the still liquid phases.
Opened containers must be resealed after removing product. If stored for long periods, the product should be overlaid with nitrogen. The product reacts with water to release carbon dioxide. During storage, transfer and handling of the product, contact with water in any form (damp containers, solvents containing water, moist air) must be prevented as the generation of carbon dioxide may result in a dangerous increase in pressure. The polyureas which are formed at the same time may result in turbidity. They may also cause blockages and breakdowns in filters, pumps and pipes.
Storage time:
Covestro represents that, for a period of twelve months following the day of shipment as stated in the respective transport documents, the product will meet the specifications or values set forth in section "specifications or characteristic data" above, what ever is applicable, provided that the product is stored in full compliance with the storage conditions set forth in and referenced under section "storage" above and is otherwise handled appropriately.
The lapse of the twelve months period does not necessaril ... text to long! (max 2000 characters)
- Recommended storage temperature: 18 - 40°C.
- Protect from moisture, heat and foreign material.
General information:
The product is sensitive to moisture and heat. It should be protected against contact with atmospheric moisture. Higher storage temperatures for prolonged periods may result in discoloration or the formation of insoluble deposits. The product crystallizes at temperatures below 18°C. However, careful melting at up to 50°C will reliquify the product without any detrimental effect on its quality. The contact surface temperature may not exceed 80°C. The reliquified product must be homogenized as crystallisation causes a shift in the isomer ratio between the crystalline and the still liquid phases.
Opened containers must be resealed after removing product. If stored for long periods, the product should be overlaid with nitrogen. The product reacts with water to release carbon dioxide. During storage, transfer and handling of the product, contact with water in any form (damp containers, solvents containing water, moist air) must be prevented as the generation of carbon dioxide may result in a dangerous increase in pressure. The polyureas which are formed at the same time may result in turbidity. They may also cause blockages and breakdowns in filters, pumps and pipes.
Storage time:
Covestro represents that, for a period of twelve months following the day of shipment as stated in the respective transport documents, the product will meet the specifications or values set forth in section "specifications or characteristic data" above, what ever is applicable, provided that the product is stored in full compliance with the storage conditions set forth in and referenced under section "storage" above and is otherwise handled appropriately.
The lapse of the twelve months period does not necessaril ... text to long! (max 2000 characters)
Sampling
The access of moisture in any form must be prevented.
Packaging Type
No data available
Technical Properties & Datasheets
Characteristics
| Property Name | Test Method | Unit | Value |
|---|---|---|---|
| Appearance | DIN ISO 6271 | Colourless to pale liquid | |
| Density 25 °C | DIN 51757 | g/cm³ | approx. 1.22 |
| Freezing point | DIN 53175 | °C | approx. 13 |
| NCO content | DIN 53185 | % by wt. | min. 48 |
| Flash point | DIN 51758 | °C | 127 |
| Viscosity 25 °C | DIN 53015 | mPa*s | approx. 3 |
Specifications
| Property Name | Test Method | Unit | Value |
|---|---|---|---|
| Purity | TDI-01-01 | % by wt. | ≥ 99.5 |
| Hydrolysable chlorine | TDI-01-03 | mg/kg | ≤ 100 |
| Acidity | TDI-01-02 | mg/kg | ≤ 40 |
| Hydrolysable chlorine | TDI-01-03 | mg/kg | ≤ 100 |
| Purity | TDI-01-01 | % by wt. | ≥ 99.5 |
| 2,4-isomer content | TDI-01-04 | % by wt. | 79.5 - 81.5 |
| Acidity | TDI-01-02 | mg/kg | ≤ 40 |
| 2,4-isomer content | TDI-01-04 | % by wt. | 79.5 - 81.5 |
Downloads
-
Technical Data Sheet
-
Safety Data SheetNo direct download available, please visit www.productsafetyfirst.covestro.com
