Before working with this product, you must read and become familiar with the available information on its risks, proper use, and handling. Information is available in several forms, e.g., in particular in the currently valid safety data sheets and product labels. For further information contact your Covestro representative.
Product description
Milky white
Applications
Dispercoll® U 58 has outstanding bonding properties on most synthetic and natural materials. Heat resistance and the resistance to plasticisers, fats and oils can be enhanced by the addition of 3 – 5 % by weight of a water-emulsible crossslinker isocyanate from the Desmodur® product line. The crosslinker isocyanate is added immediately prior to application and mixed in intensively. The pot life of the mixture must be observed. Additional resin dispersions, emulsifiers and thickeners may be added to customize certain application-specific and bonding properties.Before application, especially by spraying, the product should be filtered to remove any polymer particles which may have formed by initial drying.For heat activation bonding applications with Dispercoll® U 58, a bond line temperature in the range of approx. 50 – 70 °C is recommended to allow the dried adhesive layer to be fully activated for bonding. The actual temperature needed for a specific application will depend on the time in the press, the pressure applied and the substrates being bonded.
Form supplied
Dispersion
Specification
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Non-volatile content | (1g / 1h / 125 °C) | 49 - 51 | % | DIN EN ISO 3251 |
| Viscosity | at 23 °C,spindle L 2 / 30 rpm | 50 - 800 | mPa*s | M092-ISO 2555 |
| pH-value | 6,0 - 9,0 | DIN ISO 976 |
Typical Values
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Density | approx. 1,1 | g/cm3 | DIN 51757 | |
| Minimum film-forming temperature | > 10 | °C | DIN ISO 2115 |
Storage
- Storage in original sealed Covestro container. - Recommended storage temperature: 15 - 25 °C. Temperatures higher than30 °C should be avoided. - Protect from direct sunlight, frost, heat and foreign material. General information: The product is sensitive to temperatures below + 10°C. Temperatures below to + 10 °C can damage the product irreversibly. Prolonged storage at higher temperatures may affect the product properties. Containers must be kept sealed and protected from direct sunlight as otherwise the evaporation of water will result in the formation of a non-redispersible polymer film. After extended storage time sedimentation can occur. The material can be proceeds without quality losses after homogenization.
Storage time
Covestro represents that, for a period of six months following the day of shipment as stated in the respective transport documents, the product will meet the specifications or values set forth in section "specifications or characteristic data" above, what ever is applicable, provided that the product is stored in full compliance with the storage conditions set forth in and referenced under section "storage" above and is otherwise handled appropriately.The lapse of the six months period does not necessarily mean that the product no longer meets specifications or the set values. However, prior to using said product, Covestro recommends to test such a product if it still meets the specifications or the set values. Covestro does not make any representation regarding the product after the lapse of the six months period and Covestro shall not be responsible or liable in any way for the product failing to meet specifications or the set values after the lapse of the six months period.
Health and Safety Information
Disclaimer
General
The manner in which you use our products, technical assistance and information (whether verbal, written or by way of production evaluations), including any suggested formulations and recommendations, are beyond our control. Therefore, it is imperative that you test our products to determine suitability for your processing and intended uses. Your analysis must at least include testing to determine suitability from a technical, health, safety, and environmental and regulatory standpoint. Such testing has not necessarily been done by Covestro, and Covestro has not obtained any approvals or licenses for a particular use or application of the product.
Unless we otherwise agree in writing, all products are sold strictly pursuant to the terms of our standard conditions of sale which are available upon request.
All information and including technical assistance is given without warranty or guarantee and is subject to change without notice. It is expressly understood and agreed by you that you assume and hereby expressly release indemnify us and hold us harmless from all liability, in tort, contract or otherwise, incurred in connection with the use of our products, technical assistance, and information. Any statement or recommendation not contained herein is unauthorized and shall not bind us. Nothing herein shall be construed as a recommendation to use any product in conflict with any claim of any patent relative to any material or its use. No license is implied or in fact granted under the claims of any patent.
Non Medical and non Food Contact
This product is not designated for the manufacture of a medical device or of intermediate products for medical devices (1). This product is also not designated for other specifically regulated applications (e.g. including cosmetics, plant protection, fertilisers, plant strengtheners, food processing, food contact and others). If the intended use of the product is for the manufacture of a medical device or of intermediate products for medical devices or for other specifically regulated applications Covestro must be contacted in advance to provide its agreement to sell such product for such purpose. Nonetheless, any determination as to whether a product is appropriate for use in a medical device or intermediate products for medical devices, for Food Contact products or cosmetic applications must be made solely by the purchaser of the product without relying upon any representations by Covestro.
1) Please see the Guidance on Use of Covestro Products in a Medical Application document.
Sample
Any samples provided by Covestro are for testing purposes only and not for commercial use.
Typical value
These values are typical values only. Unless explicitly agreed in written form, they do not constitute a binding material specification or warranted values
Contact
Please use our contact form or contact us directly by sending an e-mail to technical-datasheets@cx.covestro.com .
