Before working with this product, you must read and become familiar with the available information on its risks, proper use, and handling. Information is available in several forms, e.g., in particular in the currently valid safety data sheets and product labels. For further information contact your Covestro representative.
Product description
Applications
Polyol component for two-component polyurethane resin for vacuum assisted resin transfer molding (VARTM).Baydur 120V2 in combination with Desmodur® 44CP23 is intended for the production of fiber-reinforced composites. The polyurethane resin has a very low viscosity and a long pot life at ambient temperature and a fast cure at elevated temperature.
Sampling
Moisture access should be prevented.
Specification
| Property | Test Condition | Value | Unit | Standard |
|---|---|---|---|---|
| Density at 25 °C | 1,03 | g/ml | calculated | |
| Hydroxyl number | 340 to 375 | mg KOH/g | DIN EN ISO 4629-2 | |
| Viscosity at 25 °C | 25 to 45 | mPa*s | DIN EN ISO 3219/A.3 | |
| Water content | < 0,09 | % | DIN 51777-1 |
Storage
Drums should be protected against strong sunlight and always kept sealed to protect the contents from moisture or damp air. Polyols can absorb moisture from the air and this may affect processing properties. Keep the container tightly closed in a well-ventilated place.Recommended storage temperature: 5 - 30 °CShelf life (ex works): 180 days if stored in sealed, moisture-tight containersLengthy storage can lead to a color-change from slightly purple towards yellow; in our experience this has no adverse effect on processing and product properties.
Processing
Baydur 120V2 is intended to be used in combination with isocyanate Desmodur 44CP23. Polyols can absorb moisture from the air and this may cause foaming of the resin mixture. Keep the containers tighly closed and limit exposure to moisture from the air as much as possible while transfering, before and during infusion process. When fibre-reinforced materials are prepared, moisture in the reinforcement material should be kept at a minimum to prevent foaming of the resin. It is therefore recommended to dry the reinforcement lay-up before performing the infusion.The two components should be thoroughly degassed with agitation before processing to avoid formation of bubbles in the composite.Mixing ratio
Health and Safety Information
Disclaimer
General
The manner in which you use our products, technical assistance and information (whether verbal, written or by way of production evaluations), including any suggested formulations and recommendations, are beyond our control. Therefore, it is imperative that you test our products to determine suitability for your processing and intended uses. Your analysis must at least include testing to determine suitability from a technical, health, safety, and environmental and regulatory standpoint. Such testing has not necessarily been done by Covestro, and Covestro has not obtained any approvals or licenses for a particular use or application of the product.
Unless we otherwise agree in writing, all products are sold strictly pursuant to the terms of our standard conditions of sale which are available upon request.
All information and including technical assistance is given without warranty or guarantee and is subject to change without notice. It is expressly understood and agreed by you that you assume and hereby expressly release indemnify us and hold us harmless from all liability, in tort, contract or otherwise, incurred in connection with the use of our products, technical assistance, and information. Any statement or recommendation not contained herein is unauthorized and shall not bind us. Nothing herein shall be construed as a recommendation to use any product in conflict with any claim of any patent relative to any material or its use. No license is implied or in fact granted under the claims of any patent.
Non Medical and non Food Contact
This product is not designated for the manufacture of a medical device or of intermediate products for medical devices (1). This product is also not designated for other specifically regulated applications (e.g. including cosmetics, plant protection, fertilisers, plant strengtheners, food processing, food contact and others). If the intended use of the product is for the manufacture of a medical device or of intermediate products for medical devices or for other specifically regulated applications Covestro must be contacted in advance to provide its agreement to sell such product for such purpose. Nonetheless, any determination as to whether a product is appropriate for use in a medical device or intermediate products for medical devices, for Food Contact products or cosmetic applications must be made solely by the purchaser of the product without relying upon any representations by Covestro.
1) Please see the Guidance on Use of Covestro Products in a Medical Application document.
Sample
Any samples provided by Covestro are for testing purposes only and not for commercial use.
Typical value
These values are typical values only. Unless explicitly agreed in written form, they do not constitute a binding material specification or warranted values
Contact
Please use our contact form or contact us directly by sending an e-mail to technical-datasheets@cx.covestro.com .
